High-Performance RF & Microwave PCB Manufacturing

GemTech PCB specializes in high-frequency RF and microwave PCB manufacturing for 5G base stations, 77 GHz automotive radar, and satellite communications. We optimize hybrid stackups (e.g., Rogers + FR-4) to balance RF performance and CTE mismatches, preventing delamination under thermal stress.

With in-house expertise in PTFE and ceramic-filled laminate processing, we handle challenging PTH (Plated Through Hole) metallization and specialized drilling to deliver tight impedance control down to ±5%.

OUR CAPABILITIES

PTFE & Ceramic
Material Processing

Learn More →

Challenging
PTH Metallization

Learn More →

Specialized
Drilling

Learn More →

Tight Impedance
Control

±5%


Designed for High-Frequency Applications

Deep high-frequency application experience means zero learning curve between our factory and RF designers—from STC Dk phase drift in 77 GHz radar to vacuum outgassing in spaceborne hardware. By evaluating your stackups with deep RF expertise, we deliver rapid RF PCB DFM feedback and precision engineering turnaround.

Application

Key Constraints & Considerations

Key Material Selection Criteria

Sub-6 GHz Communications

Power handling vs. transmission loss balance; thermal dissipation

Dissipation Factor (Df), Thermal Conductivity, Copper Weight / Thickness

76–81 GHz Automotive Radar

Phase stability and phase drift over temperature

Thermal Coefficient of Dielectric Constant (TCDk), Dk Tolerance, Dissipation Factor (Df)

Spaceborne & Phased-Array Systems

Vacuum outgassing requirements for space-exposed materials

ASTM E595 Outgassing Data: Total Mass Loss (TML), Collected Volatile Condensable Materials (CVCM); acceptance limits per project

24 GHz+ mmWave Front-Ends

Tight insertion loss budget; conductor loss control

Df at Operating Frequency, Copper Surface Roughness (Profile), Measured Transmission-Line Loss

RF PCB Case Studies

Field-Proven Hybrid Applications:

Hybrid material integration: managing CTE mismatch between high-frequency laminates and FR-4 to reduce lamination warpage and delamination while maintaining impedance consistency.

Phased Array RF Antenna PCBs

High-count element array routing with extreme surface coplanarity and tight phase-matching impedance across large board formats.

Discuss Similar Project ↗

Rogers + FR4 HDI Industrial Sensor Boards

Microvia laser drilling and fine-line etching integrated into high-density hybrid stackups for compact industrial sensing.

Discuss Similar Project ↗
RF and microwave PCB

Commercial RF Antenna Boards

High-yield volume fabrication balancing low-loss high-frequency layers with robust FR-4 structural bases.

Discuss Similar Project ↗

RF PCB Materials and Stackups

With in-house expertise in PTFE and ceramic-filled laminate processing, we handle challenging PTH (Plated Through Hole) metallization and specialized drilling to deliver tight impedance control down to ±5%.

PTFE & Ceramic-Filled Substrates

Rogers RO4000 & RO3000 Series (RO4350B, RO4003C, RO3003)

Extreme low loss tangent (Df down to 0.0010) and stable dielectric constant (Dk) across wide temperature ranges. Engineered specifically for 77 GHz radar front-ends, base station antennas, and satellite ground transceivers.

Dk @ 10GHz: 3.00–3.66 ±0.04 · Loss Tangent (Df): 0.0013 (RO3003)

Hydrocarbon / Ceramic Laminates

Isola Astra MT77 & I-Tera MT40 / Shengyi

Exceptional thermal conductivity and dimensional stability across broad thermal cycling regimes. Specifically qualified for millimeter-wave active phased array antenna arrays, radar transceivers, and extreme environmental exposure.

Dk Stability: ±0.05 across -40°C to +140°C · Tg: >200°C (DMA)

Advanced Hybrid Multilayer Stackups

Rogers + High-Tg FR-4 (Shengyi S1000-2M / IT-180A)

Sequential lamination optimizing microwave propagation on outer RF core layers while using robust high-Tg FR-4 inner layers for digital logic, power distribution, structural rigidity, and BOM cost efficiency.

CTE Z-Axis Match: Balanced <45 ppm/°C · Hybrid lamination: project-dependent

Discuss Material Selection →

RF & Microwave PCB  Manufacturing Capabilities

Our RF boards production complies with IPC-6018 Class 3 standards. Advanced RF fabrication processes support high-frequency signal integrity and dimensional stability.

Impedance Control:

Verified via 100% TDR coupons (±5% standard, ±3% tight control).

Dielectric Integrity:

Optimized vacuum lamination to control Dk / Df drift across high-frequency layers.

Thermal Management:

Solid copper paths, coin insertion, and IPC-4761 Type VII via filling.

Routing Density:

2 mil / 2 mil min line/space and laser microvia capability for mmWave packaging.

The following outlines RF & microwave PCB manufacturing capabilities covering layer count, circuit geometry, via structures, materials, surface finishes and engineering review. Confirm project-specific limits with the engineering team.

Category

Parameter

Manufacturing Capability

Layer Count & Lamination

Maximum Layer Count

Up to 24 Layers

Layer Count & Lamination

Lamination Process

Sequential Lamination for Multilayer RF PCB Designs

Circuit & Impedance Control

Controlled Impedance Tolerance

Standard: ±10%; Tight Tolerance: ±5%

Circuit & Impedance Control

Minimum Trace Width / Spacing

75 µm / 75 µm (3 / 3 mil)

Drilling & Via Technology

Minimum Laser-Drilled Microvia Diameter

50 µm (0.05 mm)

Drilling & Via Technology

Minimum Mechanical Drill Diameter

0.105 mm

Drilling & Via Technology

Via Structures

Blind Vias, Buried Vias, Stacked Vias, Staggered Vias

Drilling & Via Technology

Via Filling

Copper-Filled Vias, Resin-Filled Vias

RF PCB Materials

Supported Materials

PTFE, Rogers, Isola, Low-Loss FR-4, Hybrid Stack-ups

Surface Finishes

Available Finishes

ENIG, Immersion Silver, Immersion Tin, Hard Gold Plating

Copper Foil Options

Copper Foil Types

Standard, Low-Profile (LP), Very Low-Profile (VLP) Copper Foil

Quality Testing

Electrical Testing

100% Electrical Continuity and Isolation Testing

RF Performance & Engineering Support

RF PCB Manufacturing

Multilayer RF PCB Manufacturing with Controlled Impedance and Low Insertion Loss

RF Performance & Engineering Support

Engineering Review

Material Selection, Stack-up Design Review, and Process Optimization Based on RF Requirements

Testing and Quality Assurance

Over 15 years of hands-on expertise in RF boards volume production, we take total ownership of product reliability. Our RF PCB quality system eliminates common production defects at the source:

All RF boards undergo 100% TDR impedance testing per IPC-TM-650, with full compliance reports included upon delivery.

Frequently Asked Questions

Technical considerations and layout recommendations for RF PCB engineering

What are the key DFM layout guidelines for high-frequency RF PCBs?

High-frequency RF PCB layout requires strict control over controlled-impedance trace geometries, ground stitching via spacing (< λ/10), and layer transitions to minimize insertion loss and radiation. Ensure solid, uninterrupted reference ground planes directly underneath RF traces and use curved corners instead of 90-degree corners to avoid impedance discontinuities.

How do you select materials for RF PCBs, and when should you use hybrid stackups?

Material selection is governed by operating frequency, allowable dissipation factor (Df), and thermal demands. Hybrid stackups such as Rogers + FR-4 balance high-frequency performance with overall board cost by placing specialized substrates on RF layers and FR-4 cores for power, ground and structural rigidity.

What capabilities should you verify when choosing an RF PCB manufacturer?

Evaluate impedance verification, backdrilling precision, hybrid lamination experience, PTFE hole-wall preparation, low-loss surface finishes and applicable certifications. Confirm whether TDR coupon testing and IPC-6018 Class 3 / IATF 16949 compliance apply to your project.

Why do RF simulation results differ from fabricated board performance?

Fabrication tolerances, batch-to-batch material variation and missing parasitic details can shift insertion loss and impedance from a nominal simulation. Include trace width, copper roughness, lamination offsets, connector launch and via geometry in the engineering review.

Talk to us about your PCB project.

Tell us about your board type, key specifications and production target. The team can follow up to clarify technical details and next steps.

National High-tech Enterprise

Company credential — verify current certificate

Specialized & Innovative SME

Company credential — verify current status

ISO 9001:2015

Quality management system

IATF 16949:2016

Automotive quality management

ISO 14001:2015

Environmental management system

UL / CQC

UL file E470791 and CQC — verify scope

Please confirm the validity, issuing entity and applicable scope of all certifications before publishing certificate marks or making compliance claims.

Project enquiry

Fields marked * are required.

This enquiry panel is ready to connect to your WordPress form handler.